MARK: The 2-inch Watts 007DCDA is a double check detector assembly. It utilizes a ½-inch model 007 DCA for a bypass assembly. The bypass arrangement also contains a 5/8-inch-by-¾-inch bypass meter. Production of the original unit began in 1998. The model 007DCDA(M1) was introduced in 2011. The changes were to the device body and the bypass piping. The repair procedures and replacement parts are the same for both assemblies. There are no special tools needed to make this repair.
Is this you? As a journalist, you can create a free Muck Rack account to customize your profile, list your contact preferences, and upload a portfolio of your best work.
Claim your profile
Articles by Mark Inman
4” Wilkins Model 350ASTDA
DOUG: The Wilkins 350ASTDA is a double check detector assembly (DCDA). It is available in 2 ½” – 10″ sizes and has been in production since 2011. The body is made of stainless steel. The 350ASTDA utilizes a ¾” 950XLD for the bypass assembly. The repair procedures for the 350ASTDA series are similar to the 350ADA series, but it is important to note that the internal parts are different and do not interchange. No special tools are needed to repair this assembly.
Thyrotoxicosis
Ayuda Buscar en la ayuda Buscar en la ayuda Thyrotoxicosis [1] Department of Emergency Medicine, Brooke Army Medical Center Localización: Endocrinology and metabolism clinics of North America, ISSN 0889-8529, Vol. 55, Nº. 1, 2026, págs. 83-98 Idioma: inglés Enlaces Texto completo Resumen Hyperthyroidism is a spectrum of diseases encompassing subclinical hyperthyroidism, overt thyrotoxicosis, and thyroid storm.
1” Wilkins Model 720A » Working Pressure Magazine
DOUG: The Wilkins 720A is a pressure vacuum breaker that is offered in 1/2” – 2” sizes. The original version began production in 1975 as the Model 720. In 1984, Wilkins redesigned the air inlet valve, and the model number became 720A. The “A” air inlet valve will work for both the 720 and 720A. Prior to 2010, the test cocks were located on the body of the assembly. After 2010, the test cocks were located on the ball valves. Fortunately, no special tools are needed to work on this unit.
2” Febco Model 825Y » Working Pressure Magazine
MARK: Febco began producing the model 825Y in 1978. It is a reduced pressure principle assembly and is offered in 1/4″ – 2” sizes. This series uses poppet style check valves. Early models of the 825Y series did not have replaceable check seats. Replaceable check seats became standard in 1994. The only special tool required is used when replacing the check seats. A lead-free version (LF825Y) was introduced in 2010 and uses the same service procedures and internal parts as the 825Y.
3” Watts Model 009 » Working Pressure Magazine
MARK: The 3” Watts Model 009 is a reduced pressure principle assembly. Production of this unit began in 1989. A lead free version (LF009) was introduced in 2010. The leaded bronze parts were replaced with plastic or stainless steel materials, but the repair procedures and replacement parts are the same for both assemblies. There are no special tools needed to make this repair. This unit has a single access cover that is o-ring sealed and is secured by six hex head bolts.
Ames 4” Model 3000SS » Working Pressure Magazine
MARK: The cam checks for this model normally should not be that difficult to remove. The thread pattern for each cam check is very large, so it is nearly impossible to cross thread into the body. First, let’s take a quick look at how the manufacturer instructs us to properly remove the checks. The first check needs to be removed before the second check.
4” Wilkins Model 350ASTDA » Working Pressure Magazine
MARK: The Wilkins 350ASTDA is a double check detector assembly (DCDA). It is available in 2 1/2″-10″ sizes and has been in production since 2011. The body is made of stainless steel. The 350ASTDA utilizes a 3/4″ 950XLD for the bypass assembly. The repair procedures for the 350ASTDA series are similar to the 350ADA series, but it is important to note that the internal parts are different and do not interchange. No special tools are needed to repair this assembly.
4” Deringer Model 30 » Working Pressure Magazine
Question: I need to service a 4” Deringer Model 30. Can you tell me how to change the rubber components on the mainline check valves and the bypass check valve? Mark: The Deringer Model 30 is a double check detector assembly. Production began in 2014. The Model 30 has a type-II bypass arrangement, which incorporates a single check valve. The check valves for the mainline assembly are modular in design. There are no special tools needed to service this assembly.
4” Ames Model C500 » Working Pressure Magazine
Question: I am servicing a 4” Ames Model C500. Can you tell me about this assembly and how to change the rubber parts for the checks and relief valve? Mark: The Ames Model C500 is a reduced pressure principle detector assembly. Production of this unit started in 2002. The bypass assembly for this model is either an Ames ¾” 400B or a Watts ¾” 919. The check valves for the Ames C500 are modular in design and the relief valve is mounted on the outside of the assembly.
6” Watts Model 909 » Working Pressure Magazine
Question: I have a 6” Watts model 909 reduced pressure principle assembly with a badly worn and pitted first check valve seat. Are these seats threaded into the body? If so, do I need a special tool to remove the seat? Mark: The check valve seats for the Watts 6” 909 are not threaded into the body of the device. The check valve seats are o-ring sealed and held into place by (2) retaining wires or clips that are installed at approximately the 5 o’clock and 7 o’clock positions of the seat.
4” Apollo DCDA 4A » Working Pressure Magazine
Question: I have a 4” Apollo DCDA 4A that needs service. I am not familiar with this unit. What is the best way to remove the check valves from the body? Can the check discs be replaced? Mark: The Apollo DCDA 4A began production in 2008 and is a double check detector assembly (DCDA). The body is made of stainless steel and no special tools are needed to repair the assembly. This unit has a single access cover for both checks, which is sealed by an o-ring and has no spring load.
Flomatic 3" Model RPZ " Working Pressure
Question: I have a 3” Flomatic model RPZ that needs repair. Can you give me some basic information about this assembly? Are there any repair tips I should know? Doug: Production for the Danfoss/ Flomatic model RPZ was from 1993 to 2013. The 3” size uses a ductile iron body that is fused epoxy coated. These units have a single access cover that is sealed by the relief valve diaphragm. The check valves are modular in design and the springs are contained.
Ames 4” Model 3000SS » Working Pressure
Question: I have an Ames 4” Model 3000SS that I’m trying to repair. I was told that the check valves are threaded into the body of the device and unscrew counterclockwise. I can’t seem to get them to even budge. I’m afraid that if I apply much more pressure, I’m going to break something. Could the checks be cross-threaded? Mark: Typically, the cam checks for this model shouldn’t be that difficult to remove.
Wilkins 1” Model 720A » Working Pressure
Question: I need to service a Wilkins 1” Model 720A. Can you tell me if there are any special tools that I will need, and provide any helpful hints for repairing this assembly? Doug: Before we go over the repair steps, let’s take a quick look at this unit. The Wilkins 720A is a pressure vacuum breaker that is offered in ½”- 2” sizes. The original version began production in 1975 as Model 720. In 1984, Wilkins redesigned the air inlet valve and the model number became 720A.
1” Apollo Model RPLF4A » Working Pressure
Question: I am repairing a 1” Apollo Model RPLF4A. Are there any special tools I will need to complete the job? Mark: Conbraco/Apollo Model RPLF4A is a reduced pressure principle assembly. Production of this assembly began in 2011. The body of the RPLF4A is made of lead-free bronze. The standard version of this model (RP4A) looks very similar in construction, but the body is made of a leaded bronze. The repair procedures are the same for both models.
Contribution of Glucose Meter Error to Misclassification of Neonatal Glycemic Status
Glucose point-of-care testing in the neonatal intensive care unit, as the basis for informing clinical decision-making and treatment of neonatal hypoglycemia, has been extensively adopted as a preferred clinical tool, given its ease of use and minimal blood volume requirement to obtain a timely bedside glucose result.
Why Bitcoin Is Not A Pyramid Scheme
By Mark Inman, Ph.D. on ALTCOIN MAGAZINE I hear it often. On the news, in forums, on YouTube: “Bitcoin is a Pyramid Scheme.” Either these people are ignorant about Bitcoin, ignorant about pyramid schemes or just plain lying to your face. Here’s why: A pyramid scheme can be identified by two key characteristics: A new investment pays profits to previous investment. Little to no value is created or maintained.
1” Wilkins 720A " Working Pressure
Question: I have to repair a 1″ Wilkins 720A. Can you tell me if there are any special tools that I will need, or any helpful hints that will help with this repair? Doug: Before we go over the repair steps, let’s take a quick look at this unit. The Wilkins 720A is a pressure vacuum breaker that is offered in ½”- 2” sizes. The original version began production in 1975 as the model 720. In 1984, Wilkins redesigned the air inlet valve and the model number became 720A.
3” WATTS Model 009 » Working Pressure
Question: I have a 3” Watts Model 009 that needs to be serviced. I want to replace the check valve discs and relief valve rubber goods. Can you go over the repair procedures for this assembly? Mark: The 3” Watts Model 009 is a reduced pressure principle assembly. Production of the original unit began in 1989 and a lead-free version (LF009) was introduced in 2010.
4” Conbraco Model 40-700 » Working Pressure Magazine
Question: I am servicing a 4” Conbraco model 40-700. The first check on the mainline assembly is not passing and I want to change out the check rubbers and replace the seat. Can you tell me about this assembly and how to service the check valve? Mark: The Conbraco/Apollo 40-700 is a reduced pressure principle detector assembly that was made in 3” through 10” sizes. Production of this model began in 1993 and was discontinued in 2012. The body is made of ductile iron and has a blue epoxy coating.
4” Febco Model 850 DCA » Working Pressure
Question: I will be replacing the check discs on a 4” Febco model 850 DCA. Can you give me some ideas on how to repair this assembly and if there are any special tools I will need? Mark: Fortunately, there are no special tools required to repair the Febco model 850. The check valve covers are sealed with an o-ring and secured by bolts. This model has springs that are contained as a spring module.
Inman, Graham: Commercial developers heading to smaller markets
Power center developments are traditionally thought of as projects for large urban areas. The lion’s share of attention tends to be on our state’s largest cities – Tulsa and Oklahoma City – but quietly, retailers and developers have begun to take notice of many smaller markets in the state including Ardmore, McAlester, Ada, Elk City and others.
Show More
loading
Actions
Is this you?
As a journalist, you can create a free Muck Rack account to customize your profile, list your contact preferences, and upload a portfolio of your best work.Get in touch with Mark
Contact Mark, search articles and posts on X, monitor coverage, and track replies from one place.
Learn more about Muck Rack