Is this you? As a journalist, you can create a free Muck Rack account to customize your profile, list your contact preferences, and upload a portfolio of your best work.
Claim your profile
Articles by Bryan Siepert
Adafruit QT Py ESP32-S2
What has your favorite Espressif WiFi microcontroller, comes with our favorite connector - the STEMMA QT, a chainable I2C port, and has lots of Flash and RAM memory for your next IoT project? What will make your next IoT project flyyyyy? What a cutie pie! Or is it... a QT Py?
Adafruit NeoSlider
Our family of I2C-friendly user interface elements grows by one with this new product that makes it plug-n-play-easy to add a 75mm long slide potentiometer to any microcontroller or microcomputer with an I2C port. Each breakout is 3" long and 0.8" wide, with a single linear slide pot in the center. Underneath, there are four under-lighting NeoPixels that can display any RGB color.
Trinkey True Random Number Generator
Random numbers have a lot of uses in computer programming. These can be for fun things like picking a random song, drawing to a random location, etc. On the more serious side, they are useful in the realm of cryptography. For the later, security is a primary concern, so the actual randomness of the random number becomes increasingly important. This is where using a True Random Number Generator (TRNG) is very beneficial. Don't have a TRNG? No worries.
Adafruit Monochrome 1.12" 128x128 OLED Graphic Display
This OLED goes out to all the fans who want more pixels in a smaller size! Normally our 128x64 OLEDs are the biggest ones we've stocked that can use I2C. This one is a whopping 128x128 pixels in crisp monochrome. This display is a petite 1.12" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x128 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required.
Disconnected CO2 Data Logger
YOUR NAME YOUR EMAIL You have been successfully subscribed to the Notification List for this product and will therefore receive an e-mail from us when it is back in stock! For security reasons, an e-mail has been sent to you acknowledging your subscription. Please remember that this subscription will not result in you receiving any e-mail from us about anything other than the restocking of this item.
Adafruit ATtiny817 Breakout with seesaw
YOUR NAME YOUR EMAIL You have been successfully subscribed to the Notification List for this product and will therefore receive an e-mail from us when it is back in stock! For security reasons, an e-mail has been sent to you acknowledging your subscription. Please remember that this subscription will not result in you receiving any e-mail from us about anything other than the restocking of this item.
Adafruit IS31FL3741
Add a splash of RGB LEDs to a project you're working on, with this adorable 13x9 RGB LED matrix breakout. It features -- no surprise -- 117 RGB LEDs, each one 2x2mm in size, in a 13x9 grid with 3mm pitch spacing. Unlike our 8x8 DotStar grid here, these are not NeoPixel or DotStar or other 'smart' RGB LEDs. Instead of having a li'l chip in each LED, there's one large controller chip that handles all the PWM for you.
Adafruit SCD-40 and SCD-41
Take a deep breath in...now slowly breathe out. Mmm isn't it wonderful? All that air around us, which we bring into our lungs, extracts oxygen from and then breathes out carbon dioxide. CO2 is essential for life on this planet we call Earth - we and plants take turns using and emitting CO2 in an elegant symbiosis. But it's important to keep that CO2 balanced - you don't want too much around, not good for humans and not good for our planet.
Adafruit MCP9601 I2C Thermocouple Amplifier
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The Adafruit MCP9601 I2C Thermocouple Breakout (a.k.a MCP96L01) does all that for you and can be easily interfaced with any microcontroller or single-board computer with I2C.
MacroPad 2FA TOTP Authentication Friend
Having 2 Factor Authentication (2FA) on all your accounts is a good way to keep your data more secure. With 2FA logins, not only is a username and password needed, but also a one-time-use code. There are a few different ways to get that code, such as by email, phone or SMS. But my favorite way is to do it is via a 'Google Authenticator' Time-based One Time Password, also known as a TOTP.
Adafruit TCA4307 Hot-Swap I2C Buffer
As we've been adding STEMMA QT connectors to our breakouts and dev boards, folks have been really enjoying the simplicity and speed of plugging in I2C sensors and devices for quick iteration and design. That's all good, but I2C wasn't really designed for hot-plugging. You're kinda supposed to have everything connected once on boot and never mess with it - I2C was specified for on-board connections.
Adafruit Trinkey QT2040
It's half USB Key, half Adafruit QT Py, and a lotta RP2040...it's Trinkey QT2040, the circuit board with an RP2040 heart and Stemma QT legs. Folks are loving the QT Py 2040 we made, but maybe you want something plug-and-play. So we thought, hey what if we made something like that plugs right into your computer's USB port? And this is what we came up with! The PCB is designed to slip into any USB A port on a computer or laptop.
Adafruit MLX90640 IR Thermal Camera
You can now add affordable heat-vision to your project with an Adafruit MLX90640 Thermal Camera Breakout. This sensor contains a 24x32 array of IR thermal sensors. When connected to your microcontroller (or Raspberry Pi) it will return an array of 768 individual infrared temperature readings over I2C. It's like those fancy thermal cameras, but compact and simple enough for easy integration. There are two versions: one with a wider 110°x70° field of view and one with a narrower 55°x35° field of view.
Adafruit STEMMA & STEMMA QT
You may have noticed that starting in 2018, a lot of Adafruit development boards have connectors that look like this: We call these STEMMA connectors - technically they are called 3 and 4 pin JST PH connectors. They're our way of making it easy to plug-n-play various sensors and devices without a lot of wiring. Especially when the board isn't breadboard-friendly, as above. The idea is that by having easy-to-plug cables, you can wire up things without soldering, wiring and complexity.
Zelda Thunder Helm
In this project we'll build the Thunder Helm, a unique piece of armor in The Legend of Zelda: Breath Of The Wild. It's described as a precious heirloom passed down among the Gerudo. It deflects lightning strikes and is traditionally worn only by the Gerudo chief. This helm measures 297 millimeters tall by 390 millimeters wide. The main body is printed in gold PLA while the details are painted with a metallic gold acrylic paint. We used translucent PLA to illuminate the gems on the front and sides.
Show More
loading
Actions
Is this you?
As a journalist, you can create a free Muck Rack account to customize your profile, list your contact preferences, and upload a portfolio of your best work.Get in touch with Bryan
Contact Bryan, search articles and posts on X, monitor coverage, and track replies from one place.
Learn more about Muck Rack